Universal Security Instruments MP118 Uživatelský manuál Strana 21
- Strana / 194
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
PAT700 Total Organic Carbon Analyzer – Installation Page 13
Anatel Operator Manual
Figure 2-3 PAT700 wall mount
Mounting to dual instrument poles
Follow these guidelines and refer to Figure 2-1 and Figure 2-4 to mount the analyzer to
instrument poles:
• Mount the analyzer mounting bracket to two instrument poles that are attached to a
common surface. Do not secure to two instrument poles that could move
independently.
• The instrument poles should extend at least 10 inches (254 mm) from a common rigid
base and should be no larger than 2 inches (50.8 mm) in diameter.
- ANATEL PAT700 On-line Total 1
- Organic Carbon Analyzer 1
- Table of Contents 3
- Chapter 3 Startup 4
- Chapter 4 Run Modes 4
- Chapter 5 Setup 4
- Chapter 1 Before You Begin 9
- 1.3 RFID technology 10
- 1.5 Safety 11
- 1.6 Hazard information 12
- 1.7 FCC conformance 12
- 1.8 EU directives 13
- 1.9 Precautionary labels 14
- 1.10 Symbols and marks 15
- 1.11 Patents 15
- 1.12 Definitions of terms 15
- 1.13 Customer service 16
- Chapter 2 Installation 17
- 2.2 Orientation and mounting 18
- Mounting to a wall 20
- 2.3 Plumbing connections 23
- Isolation valve 23
- Water inlet and outlet 24
- 2.4 Setting sample flow rate 26
- Power supply wiring 28
- I/O wiring 29
- Discrete inputs 30
- Discrete outputs 32
- 2.7 Serial ports 38
- 2.8 RS-232 commands 39
- Conventions 39
- Mode setup commands 40
- Data read commands 40
- Data logger commands 41
- Parameter setup command 43
- Diagnostic commands 46
- 3.3 Logging on and off 48
- Auto logoff 48
- 3.4 Home screen 49
- Sliding toolbar 49
- 3.5 Home screen data views 51
- Current tab 51
- Log view tab 53
- Graph tab 53
- 4.2 Accessing run modes 56
- 4.3 Online TOC mode 56
- Sampling with pressure 57
- 4.4 Conductivity mode 57
- 4.5 Standby mode 58
- 4.6 Offline mode 58
- 4.7 Manual TOC Sample 59
- 4.8 Self clean mode 59
- General tab 62
- Idle tab 63
- Digital control tab 64
- Stabilization tab 65
- P5 Curve 66
- 5.4 System 67
- Display tab 68
- Sounds tab 69
- Network tab 69
- Backlight tab 70
- 5.5 Alarms 71
- 5.6 Analogs 73
- 5.7 Printer 74
- Conductivity tab 77
- 5.8 Security 77
- Settings tab 79
- Users tab 80
- Audit trail tab 82
- 5.9 Bottles 84
- TOC calibration tab 84
- Conductivity calibration tab 85
- TOC validation tab 86
- System suitability tab 86
- Grab sample tab 87
- 5.10 Password 88
- 5.11 Factory 89
- Cell tab 90
- Thermistor tab 90
- User slopes tab 91
- Algorithm tab 91
- OxFiles tab 92
- Chapter 6 Bottle Mode 93
- System suitability protocol 94
- 6.2 Accessing bottle mode 94
- 6.3 Bottle mode dialog box 94
- 6.4 Run standards 95
- 6.5 TOC calibration 96
- TOC calibration setup 96
- TOC calibration procedure 97
- Operator Manual Anatel 100
- Anatel Operator Manual 101
- 6.6 Conductivity calibration 104
- Verification resistor 106
- 6.7 TOC validation 108
- 6.8 System suitability test 110
- 6.9 Grab sample 112
- 6.10 Excursion mode 116
- Excursion with validation 117
- Excursion without validation 119
- 6.11 Bottle flush mode 121
- Chapter 7 Alarms 123
- 7.2 Alarm acknowledgement 124
- 7.3 Alarm details 125
- 7.4 Alarm codes 125
- Error alarms 126
- Critical error alarms 127
- Warning alarms 127
- TOC alarms 130
- Measurement alarms 130
- Audible alarms 130
- Chapter 8 Diagnostics 131
- PAT700 lamp replacement 133
- 8.4 Tests tab 133
- RS-232 test 134
- Digital I/O test 135
- 4-20 mA output test 135
- Printer test 136
- Plumbing test 136
- Pump test 140
- Fan test 141
- RFID test 142
- 8.5 Test tab 143
- 8.6 Calibration dates tab 143
- Chapter 9 Data Review 145
- 9.3 Export data 146
- 9.4 Filter data 147
- Chapter 10 Signing On and Off 149
- 10.2 Password 150
- 10.3 Expired password 150
- 10.4 Backdoor password 150
- Chapter 11 Modbus Protocol 151
- 11.2 Modbus/TCP Driver 152
- Modbus Protocol 152
- TCP/IP Interface 153
- Data Model 154
- Data Encoding 155
- IP Address 156
- Data Dictionary 158
- Configuration Block 160
- (Format: Double Float) 164
- User Security Block 168
- 12.1 Maintenance 171
- UV Detect technology 171
- Lamp replacement procedure 172
- Self clean mode 176
- 12.2 Water filter replacement 177
- 12.3 Troubleshooting 178
- Fuse replacement 178
- Technical support 178
- Return procedures 179
- Draining the analyzer 180
- Appendix A: Specifications 183
- Physical specifications 184
- Appendix B: CE Conformance 187
Související produkty a manuály pro Detektory kouře Universal Security Instruments MP118
(10 stránky)
(18 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce